UNIVERSAL QUICK FINISH CLEAR
#555 UNIVERSAL QUICK FINISH
CLEARCOAT 4.2 VOC (NR)
PRODUCT DESCRIPTION:
ADVANTAGE #555 UNIVERSAL QUICK FINISH Clearcoat 4.2 VOC was
designed to offer ease of application, great flow and leveling,
superior gloss & DOI in a highly productive 2K polyurethane
clearcoat. Under the proper conditions #555 can be polished in
as little as 90 minutes.
SURFACE PREPARATION:
Apply Undercoats and Basecoat per manufacturer’s instruction.
Over OEM or completely cured previously painted substrates scuff
with a gray scuff pad or 600 grit then wipe clean with Wax &
Grease Remover. Allow basecoat adequate flash time (follow
manufacturer’s recommendation). Follow basecoat manufacturer’s
recommendation for recoat intervals.
MIXING DIRECTIONS:
Mix 4 parts #555 clear with 1 part #551, #552, or #553 activator
by volume. Activator selection should be based on the size of
the part to be painted and the temperature of both the air and
part at time of painting.
APPLICATION DIRECTIONS: | |
Number of Coats:
2-3 wet coats Application Density: Medium-wet to wet Overlap: 50% Flash: Follow recommendations in "Dry Time" section |
|
Application Conditions: | Minimum Temp - 50°F (Substrate Temp.) |
Max Temp - 100°F (Substrate Temp.) | |
Ambient Humidity - Less than 80% preferred |
ADDITIVES: | |
ACCELERATOR: N/A | FISHEYE: N/A |
FLEX ADDITIVE: Not required | Note: Do not spray when surface temperature is below 50°F |
SUBSTRATES:
Commercially available acrylic/cab basecoats with a VOC less
than 6.6 lbs/gal.
Properly prepared previously painted substrates
GUN SETUPS: | AIR PRESSURES | ||
CONVENTIONAL | CONVENTIONAL @ Gun | Panel | OVERALL |
Gravity Feed: 1.3 mm - 1.5 mm |
Gravity Feed: | 35-45 psi | 45-50 psi |
Siphon Feed: 1.6 mm - 1.8 mm |
Siphon Feed: | 35-45 psi | 45-50 psi |
HVLP: 1.3 mm - 1.6 mm |
HVLP @ Cap: | 6-8 psi | 9-10 psi |
FLASH/DRY TIMES: | |||
Dry Times: | 551 @ or above 77°F |
552 @ or above 85°F |
553 @ or above 95°F |
Flash Between Coats | 3-5 min | 5-7 min | 5-10 min |
Dust Free | 5-7 min | 7-10 min | 10-15 min |
Sand/Polish | 1.5-2 hours | 1.5-2 hours | 1.5-2 hours |
Force Dry (Convection Heat) |
#551 | #552 | #553 |
Purge time before applying heat | 0-10 min | 0-10 min | 0-10 min |
Force Dry Time | 20 min @ 165°F | 20 min @ 165°F | 20 min @ 165°F |
Sand and Buff | After Cool Down | After Cool Down | After Cool Down |
CLEAN-UP & STORAGE:
Clean spray equipment immediately after use with Acrylic Lacquer
Thinner or Urethane Reducer. Do not leave material in spray gun.
PRODUCT TECHNICAL DATA: | |
Mix Ratio: | 4 parts clearcoat: 1 part activator |
Density: | 8.69 lbs/gal (unactivated) |
Solids (Ready to Spray) | |
By Weight | 37.71% |
By Volume | 32.5% |
VOC (Volatile Organic Content): | 4.2 lbs/gallon (ready to spray) |
Viscosity: | 17-20 seconds Zahn #2 |
Flash Point: | -4°F |
Theoretical Coverage: | 510 ft2/gal @ 1 mil thickness |
Pot Life: | 1-4 hours depending on activator selection |
*NOTE: Some spray gun
manufacturers have specific recommendations for specific
spray guns & product viscosity, always check spray gun manufacturer’s recommendation. |
Part #: ADV.55501
Price and Units
Units: GALLON
Units: GALLON Product Links: Product Information Technical Data Sheet MSDS |
Customers Who Looked At This Item Also Looked At:
QUICK FINISH URETHANE CLEAR |
|
FAST ACTIVATOR FOR 550 CLEAR |
|
MEDIUM ACTIVATOR FOR 550 CLEAR |
|
HOT ACTIVATOR FOR 550 CLEAR |
|