QUICK FINISH URETHANE CLEAR
#550 UNIVERSAL URETHANE
CLEARCOAT 4.4 VOC (NR)
PRODUCT DESCRIPTION:
ADVANTAGE #550 UNIVERSAL URETHANE Clearcoat 4.4 VOC was designed
for overall and panel refinishing. It is a fast drying, user
friendly clearcoat that produces an extremely durable finish.
Excellent for use in air and force dry environments.
SURFACE PREPARATION:
Surface must be clean, dry, and free of any contaminants, such
as wax, oil, etc. Always wash vehicle with soap and water. Wipe
surface with Wax & Grease Remover. Abrade the surface to remove
any corrosion. Re-clean area with Final Wipe - Wax & Grease
Remover. Prime bare metal with appropriate primers.
MIXING DIRECTIONS:
Mix 4 parts #550 clear with 1 part #551, #552, or #553 activator
by volume. Activator selection should be based on the size of
the part to be painted and the temperature of both the air and
part at time of painting.
APPLICATION DIRECTIONS:
1. Adjust air pressure to 45-50 psi (Siphon); 35-40 (Gravity @
Gun); 30-40 (HVLP), 6-8 psi (@ cap).
2. Apply 3 full wet coats.
3. Allow 10-15 minutes flash time between coats. Keep spray gun
6-10 inches from substrate to avoid problems associated with air
entrapment.
4. Allow to dry overnight before exposing to the weather.
ADDITIVES: | |
ACCELERATOR: N/A | FISHEYE: N/A |
FLEX ADDITIVE: Not required | Note: Do not spray when surface temperature is below 50°F |
SUBSTRATES:
Commercially available acrylic/cab basecoats with a VOC less
than 6.6 lbs/gal.
Properly prepared previously painted substrates
GUN SETUPS: | AIR PRESSURES | ||
CONVENTIONAL | CONVENTIONAL @ Gun | OVERALL | |
Gravity Feed: 1.3 mm - 1.5 mm |
Gravity Feed: | 35-40 psi | |
Siphon Feed: 1.3 mm - 1.5 mm |
Siphon Feed: | 45-50 psi | |
HVLP: 1.3 mm - 1.5 mm |
HVLP: HVLP @ Cap: |
30-40 psi 6-8 psi |
FLASH/DRY TIMES: | |||
Dry Times: | 551 @ or above 77°F |
552 @ or above 85°F |
553 @ or above 95°F |
Dust Free | 15 minutes | 20 minutes | 25 minutes |
Tack Free | 15 minutes | 20 minutes | 25 minutes |
Wet Sand or Buffable | 8-10 hours | 10-12 hours | 12-14 hours |
Delivery | overnight | overnight | overnight |
CLEAN-UP & STORAGE:
Clean spray equipment immediately after use with Acrylic Lacquer
Thinner or Urethane Reducer. Do not leave material in spray gun.
PRODUCT TECHNICAL DATA: | |
Mix Ratio: | 4 parts clearcoat: 1 part activator |
Catalyst: | #551 Fast, #552 Medium, #553 Slow |
Viscosity (Sprayable): | 17-19 seconds #2 Zahn |
Suggested Fluid Tip Size*: | Siphon (1.3mm - 1.5mm) Gravity (1.3mm - 1.5mm) HVLP (1.3mm - 1.5mm) |
Volume Solids (Sprayable): | 33% |
Film Build: | 0.8 - 1.0 mils per full wet coat |
Coverage: | 465 Sq. Ft. per gallon @ 1 mil |
V.O.C. (Sprayable): | 4.4 lbs/gallon |
Pot Life: | 4-5 Hours with #551, 8-10 hours with #552 or #553 |
*NOTE: Some spray gun
manufacturers have specific recommendations for specific
spray guns & product viscosity, always check spray gun manufacturer’s recommendation. |
Part #: ADV.55001
Price and Units
Units: GALLON
Units: GALLON Product Links: Product Information Technical Bulletin MSDS |
Customers Who Looked At This Item Also Looked At:
MEDIUM ACTIVATOR FOR 550 CLEAR |
|
FAST ACTIVATOR FOR 550 CLEAR |
|
MEDIUM ACTIVATOR FOR 550 CLEAR |
|
HOT ACTIVATOR FOR 550 CLEAR |
|
XTREME ORIGINAL CLEARCOAT 4.4 |
|
XTREME HARDENER 4.4 FAST |
|
XTREME HARDENER 4.4 MEDIUM |
|
XTREME HARDENER 4.4 SLOW |
|